Pyrography

pyrography doodle project by Lora Irish

Pyrography Doodles #6

Let’s finish up the pyrography wood burning steps for our Doodle Mushroom design.  During these steps we will fill the large mushroom’s stem, work the foreground mushrooms, and then work a general check of the work accomplished.

 

Please drop by our carving and pyrography pattern website, Art Designs Studio, to get your free mushroom pyrography patterns that complement this project.  The pattern package is on our home page.  The links to the previous posts for this free project are below.

Pyrograhy Doodles Page 1
Pyrograhy Doodles Page 2
Pyrograhy Doodles Page 3
Pyrograhy Doodles Page 4
Pyrograhy Doodles Page 5
Pyrograhy Doodles Page 6
Pyrograhy Doodles Page 7

Pyrography Doodle Mushroom, step 12Step 12: Pattern Fill the Stem

The large mushroom stem uses a large flower design with a curve-sectioned center, a ring of small spirals, and then layers of serrated petals.  Use the serrated petals to fill the space between your flowers.

 

 

 

 

Pyrography Doodle Mushroom, step 13Step 13: Working the Front Mushrooms

Follow the doodle pattern placement guide and work the foreground mushrooms.  Use a dark-medium setting throughout this burn.

 

 

 

 

Pyrography Doodle Mushroom, step 14Step 14: Finishing the Shading

Check your shading to strengthen any area that needs deeper tonal value work.  Also check your doodle patterns for tonal value.  You can re-burn any doodle pattern to add more value, if needed.

 

Tomorrow we will do the finishing steps to turn this Pyrography Doodle Mushroom wood burning into a desktop note board or kitchen recipe board.  See you then and thank you for reading.

Pyrography Doodles #6 Read More »

mushroom pyrography doodles by Irish

Pyrography Doodles #5

Today we will fill the top of the mushroom cap with a large doodle pattern, then adding graduated shading to the cap.  Please drop by our carving and pyrography pattern website, Art Designs Studio, to get your free mushroom pyrography patterns that complement this project.  The pattern package is on our home page.  The links to the previous posts for this free project are below.

Pyrograhy Doodles Page 1
Pyrograhy Doodles Page 2
Pyrograhy Doodles Page 3
Pyrograhy Doodles Page 4
Pyrograhy Doodles Page 5
Pyrograhy Doodles Page 6
Pyrograhy Doodles Page 7

Pyrography Doodle Mushroom Project, step 9Step 9: Doodle the Top Cap

The pattern on the mushroom cap is a very large flower pattern with long leaves, butterflies, and small daisies.  Begin the large flower at the top of the mushroom cap.  As you work the doodle pattern towards the outer edges of the mushroom cap begin filling using small daisies.  Add as many butterflies as you would like.

 

 

 

Pyrography Doodle Mushroom Project Steo 10Step 10: Shading the Cap

A second shading is worked over the entire large mushroom to deepen the tonal value along the outer edges and behind the leaf curl.  Leave the mushroom spots unworked, the white of the wood.

 

 

 

 

 

Pyrography Doolde Mushroom Project, STep 11Step 11: Working a Second Layer of Shading

To push the background leaves even deeper into the design, a third layer of shading is added.  Please follow the shaded drawing guide for your shading placement.

Please remember these are large images that you can right-hand click and save to your desktop.

See you tomorrow!

Pyrography Doodles #5 Read More »

Pyrography Doodles by Lora Irish

Pyrography Doodles #4

Small doodle patterns can be used to create the fill textures inside the sections of any pattern, adding delightful little designs to your work.  Those doodles can be repeat patterns, random fills, or large, fully complete designs.  In today’s step we will work a large floral pattern in the underside of our mushroom cap.

To provide a clear, easy-to-follow, easy-to-print image, the photos on this page are fairly large.  Please be patient as they load to your browser.  Click on any of the images to open them, full sized, in a new window.  Right hand click on the image and save it to your desktop.

 

Pyrography Doodle Mushroom by Irish, step 6Step 6  Completing the Leaves

To create more tonal values in the overall mushroom design, turn your temperature setting down to a dark-pale setting. Work the doodle fill patterns into each section, following the pattern guide. Note that the designs and patterns of the doodles are still strong even though they are worked at a pale value.

If you missed the beginning posts to this free pyrography project:
Pyrograhy Doodles Page 1
Pyrograhy Doodles Page 2
Pyrograhy Doodles Page 3
Pyrograhy Doodles Page 4
Pyrograhy Doodles Page 5
Pyrograhy Doodles Page 6
Pyrograhy Doodles Page 7

Pyrography Doodle Mushroom by Irish, step 7Step 7: Shading the Mushroom

Using a common fill pattern, shade the mushroom cap, underside, and stem. Work the shading on the left side of each area, with the darkest tonal values along the outer edge of each area. Follow the shaded drawing for placement.

 

 

 

Pyrography Doodle Mushroom by Irish, step 8Step 8: Fill the Underside of the Cap

Fill the underside of the mushroom with the large flower pattern shown on that step page. This pattern features a double scroll center with an inner ring of five petals and an outer ring of scalloped petals. Add more scalloped petals between the flowers to fill the space between each flower.

For more great patterns to use with this project, please visit our Pyrography Doodles Pattern Package on our pattern website, Art Designs Studio.

Pyrography Doodles #4 Read More »

Pyrography Doodles by Lora Irish

Pyrography Doodles #3

Pyrograhy Doodles Page 1
Pyrograhy Doodles Page 2
Pyrograhy Doodles Page 3
Pyrograhy Doodles Page 4
Pyrograhy Doodles Page 5
Pyrograhy Doodles Page 6
Pyrograhy Doodles Page 7

The images on this page are sized to print an 8 1/2″ x 11″ guide sheet which includes your sepia temperature setting, a close-up of the burning, the pyrography shading guide, and the doodle patterns used in that step.  Please be patient as the image loads.  Click on the image, allow it to load in a new window, right-hand click on the image, and choose Save to your Desktop.

Pyrograohy Doodles Mushroom Project by IrishStep 3: Medium Dark Leaf Patterns

To establish the mid-range of your tonal value, begin your pattern burns using a medium-hot setting on your tonal value scale.
Each fill pattern is a complete, small design within the boundaries of that section of the larger pattern.  Work the patterns with a fine line tip – either a ball tip or looped tip pen.  Work the patterns right to the edge of each section to give the impression that were the outlines not there the pattern would continue into the background.

For the first doodle patterns, shown in this step, I used simple repeats of small flowers, scales, and spirals.

Mushroom Pyrography DoodlesStep 4: Shading Background Areas

An unshaded background for your pattern fills allows the white of the wood to show through your line work.  You can work a common, shading fill over a section first, then lay your pattern work over that shading to darken the tonal value of the entire section.  This technique allows you to have a mid-toned background with a dark line doodle.

You can also burn your doodle pattern first then shade over that section to darken the total tonal value of that section.  This technique will darken both the background and the line doodle.

After these sections are shade the dark fill leaves are worked at a medium-hot setting to create the tonal value of pattern fill at the same color depth as the outlines of your pattern.

Pyrography Mushroom Doodles ProjectStep 5: Laying Patterns over Shading

Continue your pattern fill doodles over the shaded leaf sections noted in this step.  Work towards creating even thickness lines and consistent tonal values.

We will continue our Pyrography Mushroom Doodles on Monday, see you there and then.  We will continue to fill this mushroom pyrography doodle pattern with fun and easy to create doodle designs.  Please slip over to our craft, carving, and pyrography patterns website, Art Designs Studio, to get your free patterns for this project.  The download link is on our home page.

Pyrography Doodles #3 Read More »

Thin to Thick Outlines for Pyrography

Pyrograhy Doodles #2

The traced pattern lines of your pyrography pattern can be approached in several ways.  Let’s look at a few ideas before we begin the next step of the Mushroom Pyrography Doodle Project by Lora S. Irish.

If you are just joining this free online pyrography project please slip over to our craft, carving, and pyrography patterns website, Art Designs Studio, to get your free patterns for this project. Its the Spring 2014 package in the right hand navigation widgets. The download link is on our home page.

Pyrograhy Doodles Page 1
Pyrograhy Doodles Page 2
Pyrograhy Doodles Page 3
Pyrograhy Doodles Page 4
Pyrograhy Doodles Page 5
Pyrograhy Doodles Page 6
Pyrograhy Doodles Page 7

Defining the Boundary Lines of Your Pattern

Greenman Wood Burning by Lora IrishA simple outline burning along the tracing lines will define the pattern for you, but it can give your finished project a stiff, rigid look.  In the Green Man burning, right, all of the tracing lines were burned at a hot temperature, using an even, thin line.  This pyrography was worked to create a wood cut effect.  The entire burning was worked at one temperature setting, limiting the tonal values to just two tones – the white of the wood and the black of the burned line.

 

 

 

Shaded Mushroom Pyrography Project by Lora IrishThe traced lines of your pattern are just guide lines and do not need any burning.  You can define an area, without outlining it, by bringing your shading up to the line.  In this mushroom sample the shading touches the pattern line.  Where the shading stops defines the boundary of that area.  The few outline strokes in the finished work are accent lines only.

For our Mushroom Pyrography Doodle project we are using a full outline for all of the pattern lines.  This will create a boundary line around each of our doodle fill patterns.  To make that outline more interesting the line is worked in a thin to thick to thin width, changing the weight of the line as it moves through the pattern.

 

Temperature Setting and Pen Tips

Each variable temperature wood burning unit has its own settings for the different temperatures used to create your tonal values.  Create a sepia scale tonal value chart, using your burning unit and your pen tips, to establish the exact settings your unit used.  To learn more about tonal values please go to Wood Burning Sepia Values.

sepia scale for wood burningFor the outline burn that we will be working I have set my temperature setting to a high or hot setting.  I want a setting hot enough to burn a rich, dark brown line but not so hot that the pen tip scorches the wood outside the line.  If your pen tip is creating a light brown halo outside of the line, in the background area against the line, your burning unit is set to high.

 

ball tip wood burning penPen Tips for Fine Line Burning

I have two favorite tips that I use for my line work.  One is a medium-sized ball tip pen and the second is a medium-sized loop tip pen.  Both work excellently at any temperature setting.

loop tip wood burning pen

Keep your pen tip clean of any carbon build-up as you work.  A clean, bright tip burns a thinner, more even line.  Use a leather or synthetic strop and honing compound to clean your tips.

Mushroom Doodles Pyrography ProjectStep 2: Burn the outlines of the pattern tracing.

Using your finest line burning tip, set your temperature setting to a hot setting.

Burn along all of the pattern lines to set your design.  You want a dark, even line.

Work a second burning over the pattern lines to create a thick to thin effect in your outlines.  This adds strength to the outline, giving the line extra emphasis in the finished work, as well as interest in the changing dimensions of the line.  A close-up of the thick to thin outline is shown in the header image in this post.

Using the fine nail sanding board, lightly sand over your board to remove any rough areas caused by the hot temperature burn.  Wipe the board with a clean cloth to remove any dust.

 

Pyrograhy Doodles #2 Read More »

Scroll to Top