Six Common Chip Carving Mistakes

Do you make these common mistakes in your chip carving?

Too often a chip carved triangle is just not perfect. So let’s look at why these small errors happen and how to correct them to create the very best chip carving project you can!

common mistakes in chip carving1. RAGGED WALLS

Ragged walls can be caused by either poor quality wood or an improperly sharpened knife.  Basswood is a common chip carving wood that has finely packed, dense grain lines, and is considered an easy wood to work.  But not all basswood is adaptable to chip carving.  Avoid end grain plaques as you are cutting across the open end of the vascular bundles, which are similar to small soda straws that draw moisture up through the tree.  Also avoid ‘hardware store’ thin basswood sheets.  The 1/4″ and 1/8″ thick sheets are not the high wood quality of a 3/4″ plaque.

A dull knife tears through the wood grain instead of cutting it.  Learn how to properly sharpen your chip carving knife.  When you are concerned that your chips are repeatedly coming out rough, stop and take time to resharpen and hone your knife edge.

 

cutting triangle chips in chip carving2. ROUGH CENTER POINT IN THE CHIP WELL

Each chip should have a sharp, clean point at the center of the chip well.  This is caused because the angle of one of the side cuts did not fully reach the deep center point of the chip, where the three walls intersect.  Correct this by re-cutting that wall, taking your knife point slightly deeper.

Free form lines and straight wall cuts also can get misaligned at the center of the well.  Double check that you are using the correct hand grip on your knife and that your depth is even throughout the cutting stroke.

 

3.  STAGGERED WALL STROKES

This chip’s wall was cut with several staggered strokes.  During the cutting step either you changed the angle of your knife, or paused during the cut which misaligned the knife’s edge through the remaining stroke.  Re-cut that wall with one, smooth, clean stroke.

 

 

 

4.  THIN TOP EDGE

Your knife angle is just as important at the top of the triangle cut as it is on the wall and well.  It is easy to end up with a top edge that is not razor sharp, the preferred finish for any chip carver.  A simple wobble as you make the stroke can cause the knife to miss the fine edge of the neighboring chip.

Try turning the wood to recut the chip.  A new view of that top edge may help steady the stroke.

 

stab knife chip cuts5. WOBBLY EDGES

Every  chip carver discovers wobbly edged chip walls.  I find this problem often occurs when I am cutting through a spray adhesive paper pattern.  Both the glue and the paper can cause the knife edge to be pushed away from the pattern line.  Correct this by re-cutting the chip wall by thinly shaving just the bulge, not the points of the chip.

 

 

chip carving cuts6.  CHIP OUT

Chip outs happen and can be caused by several reasons.  If you are working on a heavy grain wood as sugar pine, the change in the grain can cause a small thin point to break free.

On soft woods, as basswood, the edge of the point can be lost because the knife was pulled out instead of lifted out of the cut.  To lift out the knife simply stop the stroke.  Gently pull the knife back along the stroke just a small bit, then lift the knife free from the cut.  Pulling on the tip of the blade at the end of the cut can add excess pressure that lifts a grain line.

Over cutting one side of the point, reaching the blade too deeply into the wood, can cause a point to chip out.  Try scoring the pattern line first by lightly cutting along the line with just the tip of your chip knife.  This pre-cuts and therefore pre-releases the wood grain at the point of the chip before you make the actual chip stroke.

Chip outs can be repaired by using wood glue and a tooth pick.  Place a small drop of glue on he board at the break out spot.  Use the toothpick to insure that the glue is deeply pressed into the chip area, not trapping any air space below the glue.  Replace the chip out and press firmly.  After about one-half hour of drying you can re-cut and sand this area.

NOTE – SANDPAPER FEELING TO THE CUTTING STROKE

It bares noting again that the greatest success with your chip carving comings with a properly sharpened chip knife.  So, please download a copy of our free, 38 page, pdf file on Easy Steps to Bench Knife Sharpening.

 

 

 

 

 

 

Chip Carving Workshop, written by Lora S Irish is available on Amazon.com.

Learn how to carve beautiful designs in wood with just a few basic knives!

  • Over 200 designs, ready to use, with layout ideas, grids, borders, and motifs
  • Step-by-step practice project helps you master the simple chip carving shapes and techniques you will need
  • Expert advice on knife selection & sharpening, how to prepare your wood blank, and how to transfer patterns
  • Tips & techniques for hand positions, knife positions, gang cutting, and how to handle a chip out
  • Blank practice grids so you can use your new chip carving knowledge to create your own designs

Chip carving, also known as spoon carving or “Kerbschnitt,” is the ideal introduction to woodcarving for beginners.

This simple traditional carving method uses just a few basic knives to remove selected chips of wood in small triangles, squares, and free-form curves, producing amazingly intricate and delicate results.

Internationally known woodcarving artist and author Lora S. Irish shows you how to get started in this venerable craft! Inside Chip Carving Workshop, Lora takes you through all the essential chip carving techniques, from tool sharpening and preparation to hand positions, chip cutting, and finishing.

You’ll discover how to use both geometric shapes and free form designs to create wonderfully detailed patterns. A step-by-step practice project shows you how to master the simple shapes that will allow you to cut any grid pattern in the book.

Hundreds of ready-to-use designs offer a rich treasury of chip carving layout ideas, grids, borders, and motifs for you to trace and reproduce in any combination or size.

Decorate household items and create artistic pieces in a variety of original designs: Hope chests, wooden spoons, jewelry chests, clocks, candle plates, serving trivets, and decorative plaques are just a few ideas for your new chip carving skills!

 

Scroll to Top