painted blue jeans

Painted Blue Jeans, Free Patterns

Drawing and Painting / By

What could be more perfect for our Free Doodle Patterns than a pair of blue jeans?  How about the fact that I picked up these brand-new, never worn jeans at my local church thrift shop for $1 !

Doodle Days #13 –  Blue Jean Painting, Wood Burn Spoons, Wood Carved Spoons, Leather Work, Free Lora S. Irish Patterns to Download, DIY Bookmaking, Bullet Journals, Scrap Booking, Card Making, Applique Quilting, Pyrography, Wood Carving

free painted blue jeans patterns

Why wear your slogan or favor designs on the sleeve of your t-shirt when you can paint them onto the legs of your favorite pair of blue jeans?

 

Supplies:

1 pair of pale-blue or medium-blue blue jeans
1 fine-point black fabric pen
medium-point fabric marking pens – black, medium-blue, and pale-blue
1 set of assorted color fabric marking pens
several 6 1/2″ squares of white cotton fabric
needle and thread
1 piece of scrap cardboard, large enough to slide inside the pant’s leg
steam iron

These are the specific sets of colors that I used to create my Painted Blue Jeans:

Colore Dual Tip Fabric Markers

Super Markers Fabric and T-Shirt Permanent Ink Pens

Best 24 Colors Fabric Markers

Sharpie Fine Point Markers, 36 piece set

Apple Barrel Acrylic Paint Set, 18 Piece

 

free painted blue jeans patterns

Step 1:  Pre-wash your jeans to remove any starch or stabilizing chemicals.  Dry the jeans thoroughly before you begin painting.

Step 2:  Download your copies of our Free Doodle Patterns, here on LSIrish.com.  Type doodles into the search box in the header.  We are on numbers 040 to 042 today, which should give you a nice selection of designs to use.

Step 3:  Cut the scrap cardboard to fit inside of the pant’s leg, so that one end of the cardboard comes out the pant’s leg at the bottom.  You can move this cardboard as you work to protect the jeans from color blending through to the other side of the jeans.

Step 4:  With a black fabric marking pen begin doodling … use a light pressure on the pen tip for the smoothest and fullest line coverage.  Mix your main designs with long flowing line breaks and fill patterns.

Step 5:  With the pale-blue fabric pen, fill the areas around your main designs with a tight dot pattern.  Let the space between the dots increase as you move away from the central line of the design.

Step 6:  With the medium-blue fabric pen, re-work the central area of the background with tightly packed dots.

Step 7:  Using a fine-point black fabric pen, work a fill pattern over the pale-blue and medium-blue dot patterns.  I used small, tightly packed circles.

Step 8:  Set your fabric pen colors according to your package directions.  My set only required a hot, steam pressing to become permanent coloring.

Step 9:  Flip your jeans over and do the back side of the leg.

Step 10:  You can create doodle designs on  the 6 1/2″ square white cotton fabric pieces using this same method.  Fill in some areas of your pattern with the bright colors from your set.  After the patch has been hot, steam ironed it is ready to sew into place, anywhere on your doodle jeans.

free painted blue jean patterns

 

Free Doodle Pattern #040

 

Free Doodle Pattern #041

 

Free Doodle Pattern #042

 

Art Designs StudioFor more great pattern ideas for your painted blue jeans, please visit ArtDesignsStudio.com

 

Painted Blue Jeans, Free Patterns Read More »

Doodle Wind Chimes, Free Craft Project

Adult Coloring / By

Doodle Days #12 –  Wood Burn Spoons, Wood Carved Spoons, Leather Work, Free Lora S. Irish Patterns to Download, DIY Bookmaking, Bullet Journals, Scrap Booking, Card Making, Applique Quilting, Pyrography, Wood Carving

Irish Doodle Pin Cushion Wind Chime

Doodle Days Clay Pot Wind Chimes

This wind chimes will add a touch of country delight to your back porch.  Its quick, easy, and fun to make a large set using graduated sizes of clay pots.

Supplies:

3 1/2″ clay pot
2 1/2 yards of 1/2″ wide burlap ribbon
2 yards of thin gray-brown twine
3 1/2″ gold-colored bells
1 – 3/4″ twine bead
acrylic glue
1 – bamboo kitchen skewer
fine-point marking pen
gold glitter glue

Step 1:  Download your free doodle patterns, here at LSIrish.com.  To discover more free patterns type doodle into the search box in the header of this page.

Step 2: Using a fine-point permanent marking pen, doodle around the lower section of the outside of your clay pot.  For contrast, leave the rim of the pot without decoration.  Work over some of your pattern lines several times to create a thick-and-thin outline effect.

Step 3:  Wrap the thin twin around the bottom edge of the rim three times.  Tie the twine tightly.  Use a few drops of acrylic glue to hold the knot and twine into place.  Allow the glue to dry.

Step 4:  Cut a 2 yard long piece of thin twine.  Thread the three gold-colored bells onto the thread, and move them to the center point of the thread.  Bring the two ends of the thread together, tie a knot with the two  threads about 1 1/2″ above the bells.

Step 5: Slide one 3/4″ twine bead onto the two threads and position the bead above the knot made in step 4.  Tie a knot in the threads that sits on top of the bead.

This wind chimes follows the same step-by-step instructions as
our Doodle Wind Chimes.  The free doodles where printed
on card stock paper, cut, and double-stick taped into place.
This is a quick wedding decoration.

Step 6:  Tie the two twine threads into a third knot the height of your clay pot  away from the top of the bead.  If your clay pot is 3 1/2″ tall, this third knot is made 3 1/2″ away from the bead.

Step 7:  Cut two 1 1/4″ long pieces from the bamboo kitchen skewer.  Tie one piece with a knot tightly above the third knot.  Slide the twine, from the inside to the outside, through the hole in the bottom of the clay pot.  Lay the second bamboo piece between the two twine ends, on the bottom of the pot, and secure with a tight knot.  These two bamboo sticks hold the bell clapper in place.

Step 8:  Hold one end of the burlap ribbon between your thumb and the side of your palm.  Open your fingers as wide as possible.  Wrap the ribbon over your fingers four to five times, leaving at least a 4″ long end.

Step 9:  Carefully remove the wrapped burlap ribbon from your hand and place it, centered, between the two twine threads.  Tie a tight knot in the twine to secure the burlap ribbons.

Step 10: Tie a knot in the twine threads 4″ to 5″ from what is now the top of your wind chime.  Clip the ends to about 1/2″ long.

Step 11:  Working one burlap ribbon loop at a time, turn each loop inside-out.  This gives your ribbon that lovely curl.

Step 12:  Use gold glitter glue to add little dots of bright, sparkling accents to your doodle pattern.  Allow  the glue to dry thoroughly, and your wind chime is ready to hang.

free tracing pattern
Free Doodle Pattern #037
Irish Doodle Pin Cushion Wind Chime
Free Doodle Pattern #038

 

 

 

 

 

 

 

Irish Doodle Pin Cushion Wind Chime
Free Doodle Pattern #039

 

Landscape Pyrography Techniques and Projects by Lora S Irish

Doodle Wind Chimes, Free Craft Project Read More »

Free Doodle Patterns

Adult Coloring / By

Doodle Days #11 –  Wood Burn Spoons, Wood Carved Spoons, Leather Work, Free Lora S. Irish Patterns to Download, DIY Bookmaking, Bullet Journals, Scrap Booking, Card Making, Applique Quilting, Pyrography, Wood Carving

DIY GiftsPin Cushion Gift

Artist morgue files are more than just a pile of pattern ideas.  Your morgue file is a great place to keep those project ideas that catch your interest.

DIY Gift Pin Cushion Project

 

Supplies:

a ball of scrap yarn
a 3 /12″ clay flower-pot
2 yards of burlap twine
acrylic glue
6 rubber bands
assorted marking pens
assorted glitter gel pens.

Instead of hot glue or white glue, we will be using the rubber bands around the yarn ball to hold the yarn in place against the inside wall of the clay pot.  This secures the yarn tightly into the pot, yet allows you to remove and replace the yarn ball if necessary.

For more free LSIrish.com Doodle Patterns type ‘doodle’ into the search box in the header of this page.

Step 1:  Using a fine point permanent marking pen, doodle assorted designs onto the lower section of your clay pot.

Step 2:  Accent the doodle designs with colored marking pens and with glitter gel pens.  Allow the gel pen work to dry for about 10 minutes before you move  to the next step.

Step 3: Wrap the burlap twine around the underside of the clay pot rim three times.  Tie the ends into a bow and clip the ends to about 2″ long.  Use several drops of acrylic glue to secure the bow and to hold the twine to the pot.  Allow to dry.

Step 4:  Grab those little bits of scrap yarn that you have been saving.  Wrap the yarn into a semi-tight ball … tighter than you would normally wrap for knitting or crochet, but not so tight that the ball becomes excessively hard.  You want your yarn ball about 1/2″ wider in diameter than the opening of your clay pot.  Tie off the end of the yarn.

Step 5:  Place five to six rubber bands around the center of your yarn ball.  Slid the yarn ball into the top of your clay pot so that the rubber bands are about 1/2″ below the pot rim.  Tuck in any loose yarn loops with your scissors.

Step 6:  Your loose straight pins, needles, and safety pins will sit nicely in the yarn ball, while your doodling will add a little sparkle and decoration to your sewing table.

Step 7:  Make another one for your favorite sewing friend!

free craft patterns
Free Doodle Pattern #034
free tracing patterns
Free Doodle Pattern #035

 

free zen doodles
Free Doodle patterns #036

 

Crafting with Gourds by Lora S IrishCrafting with Gourds, Lora S. Irish, available at Amazon.com

Free Doodle Patterns Read More »

pyrography leather

Pyrography Leather Jewelry

Leather Pyrography / By

What happens when you mix your pyrography, leather crafting, jewelry work, and lots of bright colors  …  You create unique pyrography leather jewelry.  Another free, online project at LSIrish.com.

pyrography leather jewelry

Leather Burned Jewelry Gallery of Ideas

Leather Burned Jewelry, Day One
Leather Burned Jewelry, Day Two
Leather Burned Jewelry, Day Three

free doodle pattern
Free Doodle Pattern #031
free doodle pattern
Free Doodle Pattern #032

 

 

 

 

 

 

 

free doodle pattern
Free Doodle Pattern #033

 

Doodle Days #10 –  Wood Burn Spoons, Wood Carved Spoons, Leather Work, Free Lora S. Irish Patterns to Download, DIY Bookmaking, Bullet Journals, Scrap Booking, Card Making, Applique Quilting, Pyrography, Wood Carving

Pyrography Leather Jewelry Read More »

how to transfer a pattern

How to Trace or Transfer Your Pattern

Pyrography Basics, Wood Carving Basics / By

Doodle Days #9   Wood Burn Spoons, Wood Carved Spoons, Leather Work, Free Lora S. Irish Patterns to Download, DIY Bookmaking, Bullet Journals, Scrap Booking, Card Making, Applique Quilting, Pyrography, Wood Carving,

Tracing a Pattern
There are several ways to transfer a pattern to a carving blank – carbon paper, graphite paper and pencil rubbing. All three products transfer a pattern to wood, but which you use  is determines by the craft you are working.

how to trace your pattern to the boardCarbon paper
Originally used to make multiple copies of a typed or written document, carbon paper comes in black or dark blue. Tracings made using this product have heavy, dark, bold lines. Carbon paper is perfect for transferring patterns for long-term projects, as the traced lines will not fade or rub off, even after many hours of carving work.  However, carbon paper creates a traced line that can not be erased with an eraser, and often can not be removed with fine sandpaper.  I use carbon paper with my wood carvings, but never with pyrography.

 

how to trace your pattern to the boardGraphite paper
This paper is lightweight with a waxed graphite coating on one side, and comes in both pale gray and white. When tracing a pattern, the graphite side is placed against the wood, resulting in a tracing with medium-gray colored lines. Graphite paper is available in sheets as small 8 1/2″ x 11” (216 x 279mm) and as large as 48” x 96” (1219 x 2438mm), and also comes in rolls several yards long. Graphite paper can be used several times, so keep previously used pieces for later tracings.  This product works well for both carving and wood burning.

how to trace your pattern to the boardPencil Rubbing
To use the pencil rubbing method for transferring a pattern, rub a soft #2 to #6 pencil over the back of your pattern paper. The higher the number of your pencil, the darker or blacker the rubbing will be. Then, place the pattern face up on your carving blank and begin tracing it. As you trace along the pattern lines, a thin, light gray coating of pencil will be left on the wood blank. Pencil rubbing lines can be erased using a white artist’s eraser, making it an excellent method for transferring patterns for carvings that will include some pyrography work.  This is my favorite form of tracing as it is so easily removed after your pyrography or carving work is done.

Simple steps for tracing a pattern
Tracing a pattern onto your carving blank is an important step; you want to make sure you center the pattern on the wood. Follow these steps to trace a pattern using graphite paper.

how to transfer a pattern1 Gather your supplies. To transfer a pattern to your wood blank, you will need a copy of the pattern, carbon paper, an ink pen, a ruler, a T-square, and tape.

how to transfer a pattern2 Mark the center of the blank. Using your ruler and T-square, mark the center of the carving blank using a horizontal center line and a vertical center line

how to get your pattern on the woodhow to get your pattern on the wood

 

 

 

 

 

 

 

3 Align the pattern with the center lines. Fold the copy of the pattern into quarters. Place the pattern on the blank, aligning the fold lines in the paper with the center lines drawn on the blank. Tape the pattern into place .

pattern tracing4 Adjust the pattern as needed to fit the shape of the wood.  For our sample tracing the board has a curved top that affects the placement of the pattern.  By sliding the design down along the vertical line the square pattern is now centered to the square area of the plaque.

how to trace a pattern for wood burning5 Place the carbon paper, and trace. Mark any adjustments necessary on your pattern. Slide the carbon paper in place under the pattern paper, and trace along the outside lines of your grouped elements. Check your tracing before you remove the pattern and carbon paper to ensure you have transferred all the necessary pattern lines .

how to trace a pattern for wood burning6 Create a border if desired. If you like, you can use a compass to create an outside border or margin line around the pattern .

how to trace a pattern for wood burning7  Add in the details as you carve. As you progress through the carving stages, cut small pieces of your original pattern paper, secure them to your wood blank, and trace the fine line details to that roughly cut areas.

8 Print several copies of your pattern.  As you work you will often find that your carving will cut away some areas of the traced pattern or that your burned shading will obscure some areas of your traced line.  You can cut small sections of your extra pattern out from the larger design and spot trace as needed.

 

finishing and paintinf techniques for wood

How to Trace or Transfer Your Pattern Read More »

Scroll to Top